ASROCK A75M Manuel d'utilisateur

1A75M-HVSUser ManualVersion 1.1Published June 2011Copyright©2011 ASRock INC. All rights reserved.

108. If you desire a faster, less restricted way of charging your Apple devices, such as iPhone/iPod/iPad Touch, ASRock has prepared a wonderful solu

111.3 Motherboard Layout 1 ATX 12V Power Connector (ATX12V1) 16 COM Port Header (COM1) 2 CPU Heatsink Retention Module 17 System

121.4 I/O Panel* There are two LED next to the LAN port. Please refer to the table below for the LAN port LED indications.

132. Installation This is a Micro ATX form factor (8.9-in x 8.5-in, 22.6 cm x 21.6 cm) motherboard.Before you install the motherboard, study the con

142.1 CPU Installation Step 1. Unlock the socket by lifting the lever up to a 90o angle.Step 2. Position the CPU directly above the socket such tha

152.3 Installation of Memory Modules (DIMM)This motherboard provides two 240-pin DDR3 (Double Data Rate 3) DIMM slots, and supports Dual Channel

162.4 Expansion Slots (PCI and PCI Express Slots)There are 1 PCI slot and 2 PCI Express slots on this motherboard. PCI Slot: PCI slot is used

172.5 AMD Dual Graphics Operation GuideThis motherboard supports AMD Dual Graphics feature. AMD Dual Graphics brings multi-GPU performance capabiliti

18 * Dual Graphics appearing here is a registered trademark of AMD Technologies Inc., and is used only for identication or explanation and to the

192. If you have installed onboard VGA driver from our support CD to your system already, you can freely enjoy the benets of dual monitor

2Copyright Notice:No part of this manual may be reproduced, transcribed, transmitted, or translated in any language, in any form or by any means, exce

20Surround Display FeatureThis motherboard supports surround display upgrade. With the internal VGA output support (D-Sub and HDMI) and external add-o

21 For Windows® 7 / 7 64-bit / VistaTM / VistaTM 64-bit OS: Right click the desktop, choose “Personalize”, and select the “Display Settings”

22* ASRock Smart Remote is only supported by some of ASRock motherboards. Please refer to ASRock website for the motherboard support list: http://ww

232.8 Jumpers Setup The illustration shows how jumpers are setup. When the jumper cap is placed on pins, the jumper is “Short”. If no jumper cap

242.9 Onboard Headers and ConnectorsOnboard headers and connectors are NOT jumpers. Do NOT place jumper caps over these headers and connectors

25Infrared Module Header This header supports an(5-pin IR1) optional wireless transmitting(see p.11 No. 20) and receiving infrared module.Front Pa

26 PLED (System Power LED): Connect to the power status indicator on the chassis front panel. The LED is on when the system is operating. The

27 Though this motherboard provides 24-pin ATX power connector, it can still work if you adopt a traditional 20-pin ATX power supply.

282.10 Serial ATA3 (SATA3) Hard Disks Installation This motherboard adopts AMD A75 FCH (Hudson-D3) chipset that supports Serial ATA3 (SATA3) hard dis

29 Caution1. Without SATA 15-pin power connector interface, the SATA3 Hot Plug cannot be processed.2. Even some SATA3 HDDs provide both SATA 15-p

3Contents1. Introduction ... 5 1.1 Package Contents ...

30 How to Hot Plug a SATA3 HDD:Points of attention, before you process the Hot Plug:Please do follow below instruction sequence to process the Hot Plu

312.13 Driver Installation GuideTo install the drivers to your system, please insert the support CD to your optical drive rst. Then, the drivers com

322.14.2 Installing Windows® 7 / 7 64-bit / VistaTM / VistaTM 64-bit With RAID FunctionsIf you want to install Windows® 7 / 7 64-bit / VistaTM / V

33Using SATA3 HDDs without NCQ and Hot Plug functions (IDE mode)STEP 1: Set up UEFI.A. Enter UEFI SETUP UTILITY Advanced screen Storage C

34STEP 1: Set up UEFI.A. Enter UEFI SETUP UTILITY Advanced screen Storage Conguration.B. Set the “SATA Mode” option to [IDE]. STEP 2:

353. UEFI SETUP UTILITY3.1 IntroductionThis section explains how to use the UEFI SETUP UTILITY to congure your sys-tem. The SPI Memory on the

363.1.2 Navigation Keys Please check the following table for the function description of each navigation key. Navigation Key(s) Function Descriptio

373.3 OC Tweaker ScreenIn the OC Tweaker screen, you can set up overclocking features.CPU CongurationSpread Spectrum This item should always be [Au

38 DRAM Timing Control Power Down EnableUse this item to enable or disable DDR power down mode. Bank InterleavingInterleaving allows memory accesse

39 Refresh Cyle Time (tRFC) Use this item to change Refresh Cyle Time (tRFC) Auto/Manual setting. The default is [Auto]. RAS to RAS Delay (tRR

43. UEFI SETUP UTILITY... 35 3.1 Introduction ...

40Instant FlashInstant Flash is a UEFI ash utility embedded in Flash ROM. This conve-nient UEFI update tool allows you to update system UEFI without

413.4.1 CPU Configuration Core C6 Mode Use this item to enable or disable Core C6 mode. The default value is [Disabled]. Package C6 M

42 3.4.2 North Bridge Configuration Primary Graphics Adapter This item will switch the PCI Bus scanning order while searching for video card. It

43 3.4.3 South Bridge Configuration Onboard HD AudioSelect [Auto], [Enabled] or [Disabled] for the onboard HD Audio feature. If you select [Auto],

443.4.4 Storage ConfigurationSATA Controller Use this item to enable or disable the “SATA Controller” feature. SATA ModeUse this item to adjust SATA

453.4.5 Super IO ConfigurationSerial Port Use this item to enable or disable the onboard serial port. Serial Port Address Use this item to set t

46 3.4.6 ACPI Configuration Suspend to RAMUse this item to select whether to auto-detect or disable the Suspend-to-RAM feature. Select [Auto] will e

47ACPI HPET table Use this item to enable or disable ACPI HPET Table. The default value is [Enabled]. Please set this option to [Enabled] if you plan

483.4.7 USB ConfigurationUSB 2.0 Controller Use this item to enable or disable the use of USB 2.0 controller.USB 3.0 Controller Use this item to en

49CPU Fan 1 Setting This allows you to set the CPU fan 1 speed. Con guration options: [Full On] and [Automatic Mode]. The default is value [Full On]

51. IntroductionThank you for purchasing ASRock A75M-HVS motherboard, a reliable motherboard produced under ASRock’s consistently stringent quality c

503.6 Boot ScreenIn this section, it will display the available devices on your system for you to cong-ure the boot settings and the boot priority.

513.7 Security ScreenIn this section, you may set or change the supervisor/user password for the system. For the user password, you may also clear it

523.8 Exit ScreenSave Changes and ExitWhen you select this option, it will pop-out the following message, “Save conguration changes and exit setup?”

534. Software Support 4.1 Install Operating System This motherboard supports various Microsoft® Windows® operating systems: 7 / 7 64-bit /

54Installing OS on a HDD Larger Than 2TBThis motherboard is adopting UEFI BIOS that allows Windows® OS to be installed on a large size HDD (>2TB).

61.2 Specifications Platform - Micro ATX Form Factor: 8.9-in x 8.5-in, 22.6 cm x 21.6 cm - Solid Capacitor for CPU power CPU - Support for Socket

7 - Supports LAN Cable Detection - Supports Energy Efcient Ethernet 802.3az - Supports PXE Rear Panel I/O I/O Panel - 1 x PS/2 Mouse Port - 1 x

8 - Hybrid Booster: - ASRock U-COP (see CAUTION 10) Hardware - CPU Temperature Sensing Monitor - Chassis Temperature Sensing - CPU/Chassis/P

9CAUTION!1. This motherboard supports Dual Channel Memory Technology. Before you implement Dual Channel Memory Technology, make sure to read the