ASROCK 775i65PE Fiche technique

1775i65PEUser ManualVersion 1.0Published October 2004Copyright©2004 ASRock INC. All rights reserved.

10Chapter 2 Installation775i65PE is an ATX form factor (12.0" x 9.0", 30.5 x 22.9 cm) motherboard. Beforeyou install the motherboard, study

11Lift Lever Up to 90°CPU Marked CornerSocket Marked Corner2.3 CPU InstallationFor the installation of Intel 775-LAND CPU,please follow the steps bel

12For proper inserting, please ensure to match the two orientation keynotches of the CPU with the two alignment keys of the socket.Step 2-3. Carefully

132.4 Installation of CPU Fan and HeatsinkThis motherboard is equipped with 775-Pin socket that supports Intel 775-LAND CPU.Please adopt the type of h

142.5 Installation of Memory Modules (DIMM)775i65PE motherboard provides four 184-pin DDR (Double Data Rate) DIMMslots, and supports Dual Channel Mem

15notchbreaknotchbreakInstalling a DIMMPlease make sure to disconnect power supply before adding orremoving DIMMs or the system components.Step 1. Unl

162.6 Expansion Slots (PCI and AGP Slots)There are 5 PCI slots and 1 AGP slot on 775i65PE motherboard.PCI slots: The PCI slots are used to install exp

172.7 Jumpers SetupThe illustration shows how jumpers aresetup. When the jumper cap is placed onpins, the jumper is “Short”. If no jumper capis placed

182.8 Onboard Headers and ConnectorsOnboard headers and connectors are NOT jumpers. Do NOT placejumper caps over these headers and connectors. Placing

19Serial ATA (SATA) Please connect the black end ofPower Cable SATA power cable to the power(Optional) connector on each drive. Thenconnect the white

2Copyright Notice:No part of this manual may be reproduced, transcribed, transmitted, or translated inany language, in any form or by any means, excep

20System Panel Header This header accommodates(9-pin PANEL1) several system front panel(see p.8 No. 15) functions.Chassis Speaker Header Please conne

212.9 Serial ATA (SATA) Hard Disks InstallationThis motherboard adopts Intel ICH5 south bridge chipset that supports Serial ATA(SATA) hard disks. You

22Chapter 3 BIOS SETUP UTILITY3.1 IntroductionThis section explains how to use the BIOS SETUP UTILITY to configure your system.The BIOS FWH chip on th

233.1.2 Navigation KeysPlease check the following table for the function description of each navigationkey.Navigation Key(s) Function Description

24Setting wrong values in this section may causethe system to malfunction.3.3.1 CPU ConfigurationBIOS SETUP UTILITYMainH/W Monitor Boot Security ExitA

253.3.2 Chipset ConfigurationRatio Actual ValueThis is a read-only item, which displays the ratio actual value of thismotherboard.CPU Thermal Throttli

26Flexibility OptionThe default value of this option is [Disabled]. It will allow better tolerance formemory compatibility when it is set to [Enabled]

273.3.3 ACPI ConfigurationRing-In Power OnUse this item to enable or disable Ring-In signals to turn on the system fromthe power-soft-off mode.PCI Dev

283.3.4 IDE ConfigurationOnBoard IDE Operate ModePlease select [Compatible Mode] when you install legacy OS (WindowsME / 98SE) into SATA device. If yo

29IDE Device ConfigurationYou may set the IDE configuration for the device that you specify. We willuse the “Primary IDE Master” as the example in the

3Contents1 Introduction ... ... 51.1 Package Contents...

30Block (Multi-Sector Transfer)The default value of this item is [Auto]. If this feature is enabled, it willenhance hard disk performance by reading o

313.3.6 Floppy ConfigurationIn this section, you may configure the type of your floppy drive.3.3.7 Super IO ConfigurationBIOS SETUP UTILITYFloppy Conf

32Parallel Port AddressUse this item to set the address for the onboard parallel port or disable it.Configuration options: [Disabled], [378], and [278

333.3.8 USB ConfigurationUSB ControllerUse this item to enable or disable the use of USB controller.USB 2.0 SupportUse this item to enable or disable

343.5 Boot ScreenIn this section, it will display the available devices on your system for you to config-ure the boot settings and the boot priority.3

353.6 Security ScreenIn this section, you may set or change the supervisor/user password for the system.For the user password, you may also clear it.3

36Discard ChangesWhen you select this option, it will pop-out the following message, “Dis-card changes?” Select [OK] to discard all changes.Load Optim

37Chapter 4 Software Support4.1 Install Operating SystemThis motherboard supports various Microsoft® Windows® operating systems:98 SE / ME / 2000 / XP

44 Software Support ... 374.1 Install Operating System ... 374.

5Chapter 1 IntroductionThank you for purchasing ASRock 775i65PE motherboard, a reliable motherboardproduced under ASRock’s consistently stringent qua

61.2 SpecificationsPlatform: ATX Form Factor: 12.0-in x 9.0-in, 30.5 cm x 22.9 cmCPU: 775-Pin Socket Supporting Intel® Pentium® 4 / Celeron® processor

7Audio Jack: Side Speaker / Rear Speaker / Central/Bass /Line In / Front Speaker / Microphone(see CAUTION 8)BIOS: AMI legal BIOS,Supports “Plug and Pl

81.3 Motherboard Layout1PS2_USB_PWR1ATXPWR1775i65PEAGP 8X1.5V_AGP1IntelICH5`IDE2IDE17.1CHUSB2.0CHA_FAN1SATA2SATA1USB671SPEAKER11PCI 1PCI 2PCI 3PCI 4AU

91.4 ASRock 8CH I/O1 Parallel Port 8 Microphone (Pink)2 RJ-45 Port 9 USB 2.0 Ports (USB01)3 Rear Speaker (Gray) 10 USB 2.0 Ports (USB23)4 S